Mirus Plugins, Conditional Actions, and HM800 Scripts
21 Jul 2023
Install Instructions:
- It is recommended that the Latest Windows Updates are installed before installing and running Mirus plugins.
- Prior to downloading, please review The Release Notes for critical setting changes and important installation requirements.
- You must have Full Windows Admin Rights to install Mirus plugins.
- Mirus 3.2 or 4.x is required to use these plugins.
If you are looking for Mirus Harvest Software, see Mirus Harvest Software.
Mirus Plugins
Windows Installer (7,8,10) | Release Notes | Supporting Documents | |
---|---|---|---|
Cone Planter | |||
Field Applicator Use with Mirus 4.1.2 |
|||
Generic Harvest Plugin User's Guide |
Generic Harvest Plugin User's Guide | ||
GNSS Attachment 2.0.0 | |||
GNSS Attachment 1.1.1 Use with Field Applicator Only |
|||
Low Yield | |||
Non-Stop Head Updated to version 1.0.5 on 11 May 2022 |
|||
Polytec NIR |
|
||
Straw Weight | |||
Zebra Label Printer |
Utilities
Supporting Documents | Software | |
---|---|---|
SCiO Troubleshooting Utility For GrainGage systems with a SCiO sensor |
SCiO Troubleshooting Guide |
Conditional Actions
Supporting Documents | Mirus 4.x | |
---|---|---|
H2C Wintersteiger Delta Sub-Sampler This controls the sub-sampler. Download the file(s) and copy to C:\HarvestMaster\Mirus\Config\ConditionalAction\Conditions. |
||
H2C Wintersteiger Quantum Sub-Sampler This controls the sub-sampler. Download the file(s) and copy to C:\HarvestMaster\Mirus\Config\ConditionalAction\Conditions. |
||
H2C Zurn150 This controls the Cyclone Air Diverter Valve and/or sub-sampler. Download the file(s). Copy the .ison files to C:\HarvestMaster\Mirus\Config\ConditionalAction\Conditions. Copy the .py files to C:\HarvestMaster\Mirus\Config\H2GrainGage\Scripts. |
|
|
H2C Almaco R1 This controls the sub-sampler and/or Air Diverter Y-valve. Download file(s) and copy to C:\HarvestMaster\Mirus\Config\ConditionalAction\Conditions. |
HM800 Scripts
Mirus < 3.1 | |
---|---|
Almaco SPC40 This controls the Diverter and AUX gates. The combine must be wired to control the cyclone and diverter separately. Primarily used in Strip Mode. |
|
BDS Script Auto - Updater This auto-updater installs the required scripts for high-capacity GrainGages with bulk density sensors (BDS). These scripts are included with Mirus version 3.2 and later. If you are using an earlier version of Mirus, run this updater after installing Mirus. The updated script files help to prevent intermittent high test weights that are caused by grain getting caught under the BDS wiper. |
|
GHM 2 - Plot This changes the sequence of the isolation door on the cyclone to allow a plot to be staged on the machine while another one is being weighed. Download the GHM 2-Plot script files. Reference the dual-bucket GHM scripts README.txt and GHM 2-plot script file instruction documents included in the .zip file. |
|
Wintersteiger Delta Tare Script for Single HCGG To prevent weight tare errors due to air blowing inside the weigh bucket during a tare check, install this script utility (the tare script must be copied from the Device folder to the Config folder). |
|
Wintersteiger Delta BDS HCGG w/ Sub-Sampler This controls the Wintersteiger sub-sampler. Download BOTH the script and setup instructions. The installer works for both standard and BDS HCGG systems. |
|
Wintersteiger Delta Classic GrainGage w/ Sub-Sampler This controls the Wintersteiger sub-sampler. Download the instructions for the Classic GrainGage sub-sampler setup and edit the existing script file as instructed. |